OMEGA2+ — OMEGA2+ Adafruit Feather HUZZAH with ESP8266 Adafruit Feather HUZZAH with ESP8266 —

Arduino Nano + I2C Adapter + I2C cable + I2C Sensor

$ 35.90$ 90.85

Features

  • Microcontroller- ATmega328
  • Architecture- AVR
  • Operating Voltage- 5V
  • Flash Memory- 32 KB of which 2 KB used by bootloader
  • SRAM- 2 KB
  • Clock Speed- 16 MHz
  • Analog IN Pins- 8
  • EEPROM- 1 KB
  • DC Current per I/O Pins- 40 mA (I/O Pins)
  • Input Voltage- 7-12 V
  • Digital I/O Pins- 22 (6 of which are PWM)
  • PWM Output- 6
  • Power Consumption- 19 mA
  • PCB Size- 18 x 45 mm

 

Clear

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328P (Arduino Nano 3.x).

Power

The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.

Memory

The ATmega328P has 32 KB, (also with 2 KB used for the bootloader. The ATmega328P has 2 KB of SRAM and 1 KB of EEPROM.

Input and Output

Each of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:

  • Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the corresponding pins of the FTDI USB-to-TTL Serial chip.
  • External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
  • PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite() function.
  • SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication, which, although provided by the underlying hardware, is not currently included in the Arduino language.
  • LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it’s off.

The Nano has 8 analog inputs, each of which provides 10 bits of resolution (i.e. 1024 different values). By default, they measure from ground to 5 volts, though is it possible to change the upper end of their range using the analogReference() function. Analog pins 6 and 7 cannot be used as digital pins. Additionally, some pins have specialized functionality:

  • I2C: 4 (SDA) and 5 (SCL). Support I2C (TWI) communication using the Wire library (documentation on the Wiring website).

There are a couple of other pins on the board:

  • AREF. The reference voltage for the analog inputs. Used with analogReference().
  • Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.


You May Also Like…


Related Products

Select your currency
Our Shipping Partners